How to make a masturbator – step -by -step instructions

How to make an inflatable masturbator?.

Now in intimate stores you can find many sex toys that can bring a lot of pleasure. However, some craftsmen manage to create such products at home. Of course, they will not have such effectiveness as professional toys, but unusual sensations are guaranteed. We will tell you how to make a masturbator using the simplest objects.

Male masturbator from a condom

There is a lot of time on a forced quarantine and you can try to do what you always put off. For example, this is the fastest and easiest way to create a full-fledged sex toy for yourself, however, it is only suitable for one-time use.

Stages of manufacture:

1. Open the contraceptive and unfold, at the end we tie a knot. A pea was added at the end to the end, but this is not necessary, since it did not bring a special effect, and besides, it can break a condom.

1. We turn the end inward by half a day so that it is at the Ring of the Product.

1. Clamp the node at the base, but try to leave a small hole, through it you need to inflate a completely condom. Inflate it and make sure that the knot does not drop, otherwise it will ruin the entire apparatus for jerking off. With fingers tightly, we clamp the base when we got a ball of the right size and carefully tie it with a thread. We do it without haste so as not to break the product.

1. As a result, the necessary hole is formed from the back, where a member will be placed later. So that the general form becomes slightly elongated and has stiffness, we wrap the upper part with tape.

As we have already said, such a masturbator is suitable only for single use, since it will be difficult to clean after that. Before use, be sure to apply a lubricant.

The product is made of ball

We have already talked about artificial vaginas, but now the turn of inflatable products. Unlike the above option, this masturbator has increased rigidity, so it can withstand large “loads”. It is not difficult to create such a design, however, during the choice of the ball, the following points should be taken into account:

• In a deflated state, it should be oblong, round will not work;
• Pay attention to the diameter of the ball ring, its size should be at least 3-4 cm when stretching and stretch well;
• Prefer a relief surface, as it will cause additional sensations.

As a result, if you are interested in the topic of how to make a masturbator for men from the ball, then based on the above moments, for these purposes this sample is suitable.

Stages of manufacture:

1. Since the material of the ball is much stronger than that of the condom, we recommend that before starting work, inflate and lower it several times. Rubber will become softer and is better for masturbation.
2. We turn the ball inside out and pull out its end, which we also tie it in the knot.

1. We leave a small hole on top and begin to inflate the ball, while holding the knot tightly so that it does not slip in. Now our design acquires the desired shape and size.

1. We pump up the air until we get the product of the desired shape. However, it is worth noting here that during the use of the Matsrubator, pressure will increase inside it, and so that it does not burst, you need to leave a little free space inside. This can be checked by bringing our product to the light.

1. We tie the back of the structure with a thread or a dense lace, only leave a small supply.

The masturbator is anal

This option, how to make a home masturbator, is characterized by a more complex work and a large number of necessary materials. However, after that we get a toy that will be very close to anal penetration.

Stages of work:

1. We dilute the jelly in approximately – 600 ml.
2. We take three condoms and pour into them 200 ml of viscous fluid. If you poured jelly with hot water, then let it cool a little so that it is easier to work.

1. The end of the condom is tied with a dense lace, we still tighten the middle of the contraceptive, as shown in the figure. We repeat the same with other rubber products.

1. The edges of each condom are associated with each other to get a ring.

1. We cut a ring from cardboard, which would match the diameter with the lower product. After that, we take another condom and pull it on our design so that its back side is placed in its back. From above we get a small hole, where it is necessary to put our penis subsequently.

Thus, the design will tightly wrap the barrel of the penis, but the surface of the toy is very soft and it may still be warm. Before each use, change the upper condom.

A toy from a glove

We complete our article by the leadership how to make a masturbator from the glove, as this is the most common and popular way. The advantage of this method is that the final product takes on the type of female buttocks, which will only strengthen excitement. By the way, do not forget about what you can learn and suck at yourself.

1. We take medical gloves for work, households will not work, since the rubber will burst at the initial stage.

1. We straighten the medical product and make nodules on the little finger and the thumb.
2. We turn the entire glove inside out, then capture the end of the middle fingers and stretch it out. Now we align it to one level with the end of the glove and tie it all into one knot. The middle finger will stick out of it a little.
3. Now we make a small incision on the ring finger, since through it we will pump the air into the glove. Pull the paste out of the ballpoint pen, and stick an empty tube into the hole on the glove, then begin to inflate it. Do it carefully so that the product does not burst.
4. When you pump the air, you get a small ball, on both sides that your fingers will stick out. They must be wrapped in the opposite direction and tied.
5. As a result, you get an item for jerking off in the form of female buttocks and with a small hole that imitates anus. Pour a lubricant into it and spend your evening with pleasure. Well, even if you didn’t manage to create your own device with our master class, you can always abandon crafts and find a partner for one night
   .

There are many more ways to make a male masturbator with improvised means. Just turn on your imagination and you can get a completely effective sex toy. Many use kitchen sponges for their purposes, toilet paper bushings, bananas skins and much more. In general, almost every thing in the house can become an object for self -satisfaction. The main thing is not to forget about safety, use condoms and lubricants. And of course, evaluate the risks of injuries. Do not forget about the possible negative consequences.